|
|
|
|
|
/** \file ssd1306.h */
|
|
|
|
|
|
#if !defined(SSD1306_H__C33398CC_133C_46F3_B9C5_5D678D1943A7__INCLUDED_)
|
|
|
|
|
|
#define SSD1306_H__C33398CC_133C_46F3_B9C5_5D678D1943A7__INCLUDED_
|
|
|
|
|
|
|
|
|
|
|
|
#include "board_config.h"
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// Success / Error
|
|
|
|
|
|
// ------------------------------------------------------------------------------------
|
|
|
|
|
|
#define SSD1306_SUCCESS 0
|
|
|
|
|
|
#define SSD1306_ERROR 1
|
|
|
|
|
|
|
|
|
|
|
|
// Address definition
|
|
|
|
|
|
// ------------------------------------------------------------------------------------
|
|
|
|
|
|
#define SSD1306_ADDR 0x3C
|
|
|
|
|
|
|
|
|
|
|
|
// Command definition
|
|
|
|
|
|
// ------------------------------------------------------------------------------------
|
|
|
|
|
|
#define SSD1306_COMMAND 0x80 // Continuation bit=1, D/C=0; 1000 0000
|
|
|
|
|
|
#define SSD1306_COMMAND_STREAM 0x00 // Continuation bit=0, D/C=0; 0000 0000
|
|
|
|
|
|
#define SSD1306_DATA 0xC0 // Continuation bit=1, D/C=1; 1100 0000
|
|
|
|
|
|
#define SSD1306_DATA_STREAM 0x40 // Continuation bit=0, D/C=1; 0100 0000
|
|
|
|
|
|
|
|
|
|
|
|
#define SSD1306_SET_MUX_RATIO 0xA8 // Set MUX ratio to N+1 MUX, N=A[5:0] : from 16MUX to 64MUX
|
|
|
|
|
|
#define SSD1306_DISPLAY_OFFSET 0xD3 // Set Display Offset
|
|
|
|
|
|
#define SSD1306_DISPLAY_ON 0xAF // Display ON in normal mode
|
|
|
|
|
|
#define SSD1306_DISPLAY_OFF 0xAE // Display OFF (sleep mode)
|
|
|
|
|
|
#define SSD1306_DIS_ENT_DISP_ON 0xA4 // Entire Display ON, Output ignores RAM content
|
|
|
|
|
|
#define SSD1306_DIS_IGNORE_RAM 0xA5 // Resume to RAM content display, Output follows RAM content
|
|
|
|
|
|
#define SSD1306_DIS_NORMAL 0xA6 // Normal display, 0 in RAM: OFF in display panel, 1 in RAM: ON in display panel
|
|
|
|
|
|
#define SSD1306_DIS_INVERSE 0xA7 // Inverse display, 0 in RAM: ON in display panel, 1 in RAM: OFF in display panel
|
|
|
|
|
|
#define SSD1306_DEACT_SCROLL 0x2E // Stop scrolling that is configured by command 26h/27h/29h/2Ah
|
|
|
|
|
|
#define SSD1306_ACTIVE_SCROLL 0x2F // Start scrolling that is configured by the scrolling setup commands:26h/27h/29h/2Ah
|
|
|
|
|
|
#define SSD1306_SET_START_LINE 0x40 // Set Display Start Line
|
|
|
|
|
|
#define SSD1306_MEMORY_ADDR_MODE 0x20 // Set Memory, Addressing Mode
|
|
|
|
|
|
#define SSD1306_SET_COLUMN_ADDR 0x21 // Set Column Address
|
|
|
|
|
|
#define SSD1306_SET_PAGE_ADDR 0x22 // Set Page Address
|
|
|
|
|
|
#define SSD1306_SEG_REMAP 0xA0 // Set Segment Re-map, X[0]=0b column address 0 is mapped to SEG0
|
|
|
|
|
|
#define SSD1306_SEG_REMAP_OP 0xA1 // Set Segment Re-map, X[0]=1b: column address 127 is mapped to SEG0
|
|
|
|
|
|
#define SSD1306_COM_SCAN_DIR 0xC0 // Set COM Output, X[3]=0b: normal mode (RESET) Scan from COM0 to COM[N –1], e N is the Multiplex ratio
|
|
|
|
|
|
#define SSD1306_COM_SCAN_DIR_OP 0xC8 // Set COM Output, X[3]=1b: remapped mode. Scan from COM[N-1] to COM0, e N is the Multiplex ratio
|
|
|
|
|
|
#define SSD1306_COM_PIN_CONF 0xDA // Set COM Pins Hardware Configuration,
|
|
|
|
|
|
// A[4]=0b, Sequential COM pin configuration, A[4]=1b(RESET), Alternative COM pin configuration
|
|
|
|
|
|
// A[5]=0b(RESET), Disable COM Left/Right remap, A[5]=1b, Enable COM Left/Right remap
|
|
|
|
|
|
#define SSD1306_SET_CONTRAST 0x81 // Set Contrast Control, Double byte command to select 1 to 256 contrast steps, increases as the value increases
|
|
|
|
|
|
#define SSD1306_SET_OSC_FREQ 0xD5 // Set Display Clock Divide Ratio/Oscillator Frequency
|
|
|
|
|
|
// A[3:0] : Define the divide ratio (D) of the display clocks (DCLK): Divide ratio= A[3:0] + 1, RESET is 0000b (divide ratio = 1)
|
|
|
|
|
|
// A[7:4] : Set the Oscillator Frequency, FOSC. Oscillator Frequency increases with the value of A[7:4] and vice versa. RESET is 1000b
|
|
|
|
|
|
#define SSD1306_SET_CHAR_REG 0x8D // Charge Pump Setting, A[2] = 0b, Disable charge pump(RESET), A[2] = 1b, Enable charge pump during display on
|
|
|
|
|
|
// The Charge Pump must be enabled by the following command:
|
|
|
|
|
|
// 8Dh ; Charge Pump Setting
|
|
|
|
|
|
// 14h ; Enable Charge Pump
|
|
|
|
|
|
// AFh; Display ON
|
|
|
|
|
|
#define SSD1306_SET_PRECHARGE 0xD9 // Set Pre-charge Period
|
|
|
|
|
|
#define SSD1306_VCOM_DESELECT 0xDB // Set VCOMH Deselect Leve
|
|
|
|
|
|
#define SSD1306_NOP 0xE3 // No operation
|
|
|
|
|
|
#define SSD1306_RESET 0xE4 // Maybe SW RESET, @source https://github.com/SmingHub/Sming/issues/501
|
|
|
|
|
|
|
|
|
|
|
|
// Clear Color
|
|
|
|
|
|
// ------------------------------------------------------------------------------------
|
|
|
|
|
|
#define CLEAR_COLOR 0x00
|
|
|
|
|
|
|
|
|
|
|
|
// Init Status
|
|
|
|
|
|
// ------------------------------------------------------------------------------------
|
|
|
|
|
|
#define INIT_STATUS 0xFF
|
|
|
|
|
|
|
|
|
|
|
|
// AREA definition
|
|
|
|
|
|
// ------------------------------------------------------------------------------------
|
|
|
|
|
|
#define START_PAGE_ADDR 0
|
|
|
|
|
|
#define END_PAGE_ADDR 3 // 7 for 128x64, 3 for 128x32 version
|
|
|
|
|
|
#define START_COLUMN_ADDR 0
|
|
|
|
|
|
#define END_COLUMN_ADDR 127
|
|
|
|
|
|
#define RAM_X_END END_COLUMN_ADDR + 1
|
|
|
|
|
|
#define RAM_Y_END END_PAGE_ADDR + 1
|
|
|
|
|
|
|
|
|
|
|
|
#define CACHE_SIZE_MEM (1 + END_PAGE_ADDR) * (1 + END_COLUMN_ADDR)
|
|
|
|
|
|
|
|
|
|
|
|
#define MAX_X END_COLUMN_ADDR
|
|
|
|
|
|
#define MAX_Y (END_PAGE_ADDR + 1) * 8
|
|
|
|
|
|
|
|
|
|
|
|
// @var set area
|
|
|
|
|
|
extern unsigned int _counter;
|
|
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
|
* --------------------------------------------------------------------------------------------+
|
|
|
|
|
|
* PRIVATE FUNCTIONS
|
|
|
|
|
|
* --------------------------------------------------------------------------------------------+
|
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
|
|
uint8_t SSD1306_Init (uint8_t);
|
|
|
|
|
|
uint8_t SSD1306_Send_StartAndSLAW (uint8_t);
|
|
|
|
|
|
uint8_t SSD1306_Send_Command (uint8_t);
|
|
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
|
* +------------------------------------------------------------------------------------+
|
|
|
|
|
|
* |== PUBLIC FUNCTIONS ================================================================|
|
|
|
|
|
|
* +------------------------------------------------------------------------------------+
|
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
|
|
void SSD1306_ClearScreen (void);
|
|
|
|
|
|
uint8_t SSD1306_NormalScreen (uint8_t);
|
|
|
|
|
|
uint8_t SSD1306_InverseScreen (uint8_t);
|
|
|
|
|
|
uint8_t SSD1306_UpdateScreen_Temp (uint8_t address);
|
|
|
|
|
|
uint8_t SSD1306_UpdateScreen (uint8_t);
|
|
|
|
|
|
uint8_t SSD1306_UpdatePosition (void);
|
|
|
|
|
|
void SSD1306_SetPosition (uint8_t, uint8_t);
|
|
|
|
|
|
uint8_t SSD1306_DrawChar (char);
|
|
|
|
|
|
void SSD1306_DrawString (char *);
|
|
|
|
|
|
uint8_t SSD1306_DrawPixel (uint8_t, uint8_t);
|
|
|
|
|
|
uint8_t SSD1306_DrawLine (uint8_t, uint8_t, uint8_t, uint8_t);
|
|
|
|
|
|
uint8_t SSD1306_DrawBackGround(void);
|
|
|
|
|
|
uint8_t SSD1306_DrawBackGround_Log(void);
|
|
|
|
|
|
uint8_t SSD1306_DrawBackGround_LeftShift(uint8_t Shift);
|
|
|
|
|
|
uint8_t SSD1306_Draw_Temperature(uint16_t Temperature);
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#if 0
|
|
|
|
|
|
#define OzOLED_Max_X 128 //128 Pixels
|
|
|
|
|
|
#define OzOLED_Max_Y 64 //64 Pixels
|
|
|
|
|
|
|
|
|
|
|
|
#define OLED_ADDRESS_W 0x3C
|
|
|
|
|
|
#define OLED_ADDRESS_R 0x3D
|
|
|
|
|
|
|
|
|
|
|
|
#define I2C_400KHZ 1 // 0 to use default 100Khz, 1 for 400Khz
|
|
|
|
|
|
|
|
|
|
|
|
// registers
|
|
|
|
|
|
#define OzOLED_COMMAND_MODE 0x80
|
|
|
|
|
|
#define OzOLED_DATA_MODE 0x40
|
|
|
|
|
|
|
|
|
|
|
|
// commands
|
|
|
|
|
|
#define OzOLED_CMD_DISPLAY_OFF 0xAE
|
|
|
|
|
|
#define OzOLED_CMD_DISPLAY_ON 0xAF
|
|
|
|
|
|
#define OzOLED_CMD_NORMAL_DISPLAY 0xA6
|
|
|
|
|
|
#define OzOLED_CMD_INVERSE_DISPLAY 0xA7
|
|
|
|
|
|
#define OzOLED_CMD_SET_BRIGHTNESS 0x81
|
|
|
|
|
|
|
|
|
|
|
|
#define OzOLED_RIGHT_SCROLL 0x26
|
|
|
|
|
|
#define OzOLED_LEFT_SCROLL 0x27
|
|
|
|
|
|
#define OzOLED_SET_VERTICAL_SCROLL_AREA 0xA3
|
|
|
|
|
|
#define OzOLED_VERTICAL_RIGHT_SCROLL 0x29
|
|
|
|
|
|
#define OzOLED_VERTICAL_LEFT_SCROLL 0x2A
|
|
|
|
|
|
#define OzOLED_CMD_ACTIVATE_SCROLL 0x2F
|
|
|
|
|
|
#define OzOLED_CMD_DEACTIVATE_SCROLL 0x2E
|
|
|
|
|
|
|
|
|
|
|
|
#define HORIZONTAL_ADDRESSING 0x00
|
|
|
|
|
|
#define PAGE_ADDRESSING 0x02
|
|
|
|
|
|
|
|
|
|
|
|
#define Scroll_Left 0x00
|
|
|
|
|
|
#define Scroll_Right 0x01
|
|
|
|
|
|
#define Scroll_Up 0x02
|
|
|
|
|
|
#define Scroll_Down 0x03
|
|
|
|
|
|
|
|
|
|
|
|
#define Scroll_2Frames 0x07
|
|
|
|
|
|
#define Scroll_3Frames 0x04
|
|
|
|
|
|
#define Scroll_4Frames 0x05
|
|
|
|
|
|
#define Scroll_5Frames 0x00
|
|
|
|
|
|
#define Scroll_25Frames 0x06
|
|
|
|
|
|
#define Scroll_64Frames 0x01
|
|
|
|
|
|
#define Scroll_128Frames 0x02
|
|
|
|
|
|
#define Scroll_256Frames 0x03
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// =================== High Level ===========================
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#define OLED_I2C_ADDRESS 0x3C
|
|
|
|
|
|
|
|
|
|
|
|
// The SSD1306 datasheet (pg.20) says that a control byte has to be sent before sending a command
|
|
|
|
|
|
#define OLED_CONTROL_BYTE_CMD_SINGLE 0x80
|
|
|
|
|
|
#define OLED_CONTROL_BYTE_CMD_STREAM 0x00
|
|
|
|
|
|
#define OLED_CONTROL_BYTE_DATA_STREAM 0x40
|
|
|
|
|
|
|
|
|
|
|
|
// Fundamental commands (pg.28)
|
|
|
|
|
|
#define OLED_CMD_SET_CONTRAST 0x81 // follow with 0x7F
|
|
|
|
|
|
#define OLED_CMD_DISPLAY_RAM 0xA4
|
|
|
|
|
|
#define OLED_CMD_DISPLAY_ALLON 0xA5
|
|
|
|
|
|
#define OLED_CMD_DISPLAY_NORMAL 0xA6
|
|
|
|
|
|
#define OLED_CMD_DISPLAY_INVERTED 0xA7
|
|
|
|
|
|
#define OLED_CMD_DISPLAY_OFF 0xAE
|
|
|
|
|
|
#define OLED_CMD_DISPLAY_ON 0xAF
|
|
|
|
|
|
|
|
|
|
|
|
// Addressing Command Table (pg.30)
|
|
|
|
|
|
#define OLED_CMD_SET_MEMORY_ADDR_MODE 0x20 // follow with 0x00 = HORZ mode = Behave like a KS108 graphic LCD
|
|
|
|
|
|
#define OLED_CMD_SET_COLUMN_RANGE 0x21 // can be used only in HORZ/VERT mode - follow with 0x00 + 0x7F = COL127
|
|
|
|
|
|
#define OLED_CMD_SET_PAGE_RANGE 0x22 // can be used only in HORZ/VERT mode - follow with 0x00 + 0x07 = PAGE7
|
|
|
|
|
|
|
|
|
|
|
|
// Hardware Config (pg.31)
|
|
|
|
|
|
#define OLED_CMD_SET_DISPLAY_START_LINE 0x40
|
|
|
|
|
|
#define OLED_CMD_SET_SEGMENT_REMAP 0xA1
|
|
|
|
|
|
#define OLED_CMD_SET_MUX_RATIO 0xA8 // follow with 0x3F = 64 MUX
|
|
|
|
|
|
#define OLED_CMD_SET_COM_SCAN_MODE 0xC8
|
|
|
|
|
|
#define OLED_CMD_SET_DISPLAY_OFFSET 0xD3 // follow with 0x00
|
|
|
|
|
|
#define OLED_CMD_SET_COM_PIN_MAP 0xDA // follow with 0x12
|
|
|
|
|
|
|
|
|
|
|
|
// Timing and Driving Scheme (pg.32)
|
|
|
|
|
|
#define OLED_CMD_SET_DISPLAY_CLK_DIV 0xD5 // follow with 0x80
|
|
|
|
|
|
#define OLED_CMD_SET_PRECHARGE 0xD9 // follow with 0x22
|
|
|
|
|
|
#define OLED_CMD_SET_VCOMH_DESELCT 0xDB // follow with 0x30
|
|
|
|
|
|
|
|
|
|
|
|
// Charge Pump (pg.62)
|
|
|
|
|
|
#define OLED_CMD_SET_CHARGE_PUMP 0x8D // follow with 0x14
|
|
|
|
|
|
|
|
|
|
|
|
// NOP
|
|
|
|
|
|
#define OLED_CMD_NOP 0xE3
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
void Oled_SendCommand(unsigned char command);
|
|
|
|
|
|
void Oled_SendData(unsigned char data);
|
|
|
|
|
|
void Oled_PrintCharXY(char C, unsigned char X, unsigned char Y);
|
|
|
|
|
|
void Oled_PrintChar(char C);
|
|
|
|
|
|
void Oled_PrintString(const char *String, unsigned char X, unsigned char Y, unsigned char numChar);
|
|
|
|
|
|
void Oled_SetCursorXY(unsigned char X, unsigned char Y);
|
|
|
|
|
|
unsigned char Oled_PrintNumberXY(long long_num, unsigned char X, unsigned char Y);
|
|
|
|
|
|
unsigned char Oled_PrintNumber(long long_num);
|
|
|
|
|
|
unsigned char Oled_PrintFloatXY(float float_num, unsigned char prec, unsigned char X, unsigned char Y);
|
|
|
|
|
|
void Oled_SetPowerOff(void);
|
|
|
|
|
|
void Oled_SetPowerOn(void);
|
|
|
|
|
|
void Oled_SetNormalDisplay(void);
|
|
|
|
|
|
void Oled_SetPageMode(void);
|
|
|
|
|
|
void Oled_ClearDisplay(void);
|
|
|
|
|
|
void Oled_Initialization(void);
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
void begin_oled_i2c_ssd1306_12864();
|
|
|
|
|
|
void oled_command(unsigned char data);
|
|
|
|
|
|
void oled_data(unsigned char data);
|
|
|
|
|
|
void oled_black_white();
|
|
|
|
|
|
void dispaly_bmp_image(unsigned char __flash *img_buf);
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#endif
|
